|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fits the 10 Frame Langstroth hives and seamlessly integrate with all Harvest Lane Honey bottom boards. With a small and medium gap, the reducer can be used to completely close off your hive for transport or as a protection from pesticide spraying. Reducers are also used to reduce the entrance of a hive during new package introduction or to prevent the hive from having to much cold air during winter. Standard usage is one reducer per hive.
|
Built from sturdy, food-grade plastic to make it resistant to wax moths and for easy acceptance in the hive. It features a text a textured cell pattern and 100% beeswax coating. Made in the USA of food grade plastic. Use with 9-1/8" Deep Brood Foundations with Groove Tops and Groove Bottoms and 9-1/2" Deep Brood Boxes.
|
Resistant to wax moths, long lasting and durable with textured cell pattern; 100% bees was coating. Made in the USA of food grade plastic. Usage: use with 6-1/4" Medium Honey Super and 6-1/4" Frames with Groove Tops and Groove Bottoms.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use with 10 Frame Langstroth hives; place the Queen Excluder between honey and brood chambers to prevent the queen from laying eggs in honey; the excluder will also allow you to find the queen easily on hive inspections. Do not add until the brood is established.
|
Use with 10 Frame Langstroth hives; place the Queen Excluder between honey and brood chambers to prevent the queen from laying eggs in honey; the excluder will also allow you to find the queen easily on hive inspections. Do not add until the brood is established.
|
Should be used as your Honey Supers or add to your hive until you are ready to extract honey. Based on the 6-7/8" 10 Frame Langstroth and made from USA Ponderosa Pine with minimal knots, grade 2 or better, this box works with any Langstroth hive. Handle grips on four sides facilitate easy handling. Frame rest lip included. Recommend assembly shortly after delivery to ensure product quality. Measurements: 16-1/4" x 19-7/8" x 6-7/8". Assembly required and assembly instructions enclosed.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Easily mounts to the side of beehive boxes for holding your frames as you inspect your hive.
|
Moisture resistant and used as a protective cover over the hive to provide extra insulation; ideal for use with standard 10 Frame Langstroth Beehives; can also prevent the hive's top from sticking to the boxes to prolong the life of your equipment; when used with a bee escape or cone, it will help the beekeeper remove bees from the hive during honey harvest. Standard usage is one inner cover per hive.
|
Designed to fit 10 Frame Langstroth hives and lasts for up to 20 years; spacing on the bottom allows for strapping your hive for transport or wind protection; standard usage is one Bottom Board per hive to be used as a base for your boxes.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ideal for use as Brood chambers in your hive. Standard use is (2) Brood Chambers per hive. Based on the Langstroth ten-frame design with standard 9-1/2" frames made from USA Ponderosa Pine with minimal knots, grade 2 or better, this box works with any Langstroth hive. Handle grips on four sides facilitate easy handling. Frame rest included. Recommend assembly shortly after delivery to ensure product quality. Measurements: 16-1/4" x 19-7/8" x 9-1/2". Assembly required and assembly instructions are enclosed.
|
Used to provide ventilation to the hive; the screened bottom board features a sliding solid bottom that allows the beekeeper to control the amount of ventilation without having to disturb the hive; consists of a 45-degree slanted front landing board with the bottom board and solid constructed sides, along with a heavy-gauge galvanized steel mesh screened center and a solid sliding bottom for long-term use.
|
Constructed of galvanized steel stop a wooden base designed to fit across a standard 10 frame Langstroth Hive and includes a drip edge to protect against the weather and pests; engineered and designed to withstand pressure over 2500 lbs. Standard use: one top per hive.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Constructed of galvanized steel stop a wooden base designed to fit across a standard 10 frame Langstroth Hive and includes a drip edge to protect against the weather and pests; engineered and designed to withstand pressure over 2500 lbs. Standard use: one top per hive.
|
Built from Ponderosa Pine and painted with two coats of white exterior latex paint, the box is ready to use as brood chambers in your Standard 6 7/8" 10 Frame Langstroth hive or as honey supers as your hive builds up. Standard use is to continue to add honey supers until you are ready to extract. Based on the standard 10 Frame Langstroth design with handle grips on 4 sides for easy handling and frame rest lip included. This product is intended for use with Medium Honey 6-14" frames and 5-5/8" foundations. The plastic foundation has a beeswax coating. Measurements: 16-1/4" x 19-7/8" x 6-7/8". NO assembly required. It comes fully assembled. Made In The USA.
|
This kit includes an assembled and painted USA Ponderrosa Pine Deep Broad bee box , as well as (10) 9-1/2" assembled and waxed Deep Honey frames with sturdy plastic foundations. Milled and assembled in the USA, the box is fully painted, then quality inspected to ensure a long lasting hive. Designed to work with all 10 Frame Langstroth design hives. Recommend (2) Deep Brood boxes while starting a hive. Measurements: 16-14" x 19-7/8" x 9-1/2".
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use to raise any standard Langstroth hive off the ground to prevent water damage and hive invasions. Standard use: one protective hive stand per hive.
|
Includes: Outer cover, Inner cover, (1) deep hive body, (1) deep frames with plastic foundation, (1) Bottom board, (1) Entrance reducer, (1) In-hive feeder, (1) 3x6 smoker, 1lb. bag of smoker fuel, (1) 9.5" steel hive tool and (1) bee brush.
|
|
|
