|
|
|
|
|
|
|
|
|
|
|
Used to support DuraSpout downspout at either the offset elbow, coupler, or discharge spout. Never needs painting. Will not rust, rot or chip.
|
Used to support DuraSpout downspout at either the offset elbow, coupler, or discharge spout. Never needs painting. Will not rust, rot or chip.
|
Used where fascia board does not exist or is not vertical. Tang nailed under shingles then screwed to support brackets and slip joints. Front hinge snapped over button on part No.RW105 and part No.RW106.
|
|
|
|
|
|
|
|
|
|
|
|
|
To support downspout at either the offset elbow coupler or discharge spout. (Estimated 70 pieces per 1000' of gutter)
|
To support downspout at either the offset elbow coupler or discharge spout. (Estimated 70 pieces per 1000' of gutter)
|
Used to support DuraSpout downspout at either the offset elbow, coupler, or discharge spout. Never needs painting. Will not rust, rot or chip.
|
|
|
|
|
|
|
|
|
|
|
|
|
Used with Repla K system or as a replacement for metal. Used where the downspout changes in any direction. Turns 112 degrees for offsets and discharge spouts.
|
Used with Repla K system or as a replacement for metal. Used where the downspout changes in any direction. Turns 112 degrees for offsets and discharge spouts.
|
Used where fascia board does not exist or is not vertical. Attaches to roof under shingles and screwed to support brackets.
|
|
|
|
|
|
|
|
|
|
|
|
|
Used with a B-style Elbow to create an offset on side of house.
|
Used with a B-style Elbow to create an offset on side of house.
|
Used to terminate either right or left gutter end, complete with Raingo seal. (Estimated 45 pieces per 1000' of gutter).
|
|
|
|
|
|
|
|
|
|
|
|
|
Used with gutter fitting to make either right or left gutter stop. (Estimated 15 piece per 1000' of gutter).
|
Basic gutter support fitting, installed every 30" of gutter length. Patented button on front for alternate use with part No. RW108. (Estimated 300 pieces per 1000' of gutter).
|
For end of gutter run.
|
|
|
|
|
|
|
|
|
|
|
|
|
For end of gutter run.
|
For end of gutter run.
|
For end of gutter run.
|
|
|
|
|
|
|
|
|
|
|
|
|
90 degree angle. Non-metallic, never needs painting. Will not rust, rot or chip. Fits anywhere downspout changes direction.
|
Used where the square downspout changes in any direction. Estimated 100 pieces per 1000' of gutter.
|
Used where the square downspout changes in any direction. Estimated 100 pieces per 1000' of gutter.
|
|
|
|
|
|
|
|
|
|
|
|
|
Used for support of gutter. Brackets can not be seen at ground level.
|
Used for support of gutter. Brackets can not be seen at ground level.
|
For joining 2 pieces of gutter; complete with seals, insertion marks. Patented button on front, alternate use with part No. RW108. (Estimated 90 pieces per 1000' of gutter).
|
|
|
|
|
|
|
|
|
|
|
|
|
Basic gutter support fitting, installed every 30" of gutter length. Patented button on front for alternate use with part No. RW108. (Estimated 300 pieces per 1000' of gutter).
|
Used with gutter fitting to make either right or left gutter stop. (Estimated 15 piece per 1000' of gutter).
|
Used to terminate either right or left gutter end, complete with Raingo seal. (Estimated 45 pieces per 1000' of gutter).
|
|
|
|
|
|
|
|
|
|
|
|
|
Connects two lengths of downspout.
|
Connects two lengths of downspout.
|
90 degree angle. Non-metallic, never needs painting. Will not rust, rot or chip. Fits anywhere downspout changes direction.
|
|